AL811H SERVICE PDF

The ALH is rated at watts CW carrier in normal CW or tune. The AL is rated at watts PEP voice, or just over watts carrier. The ALH is sold worldwide and is quite a well-built “budget” amplifier, but by no means easy to repair. To dig in the amplifier almost everything has to be. duty power supply and RF components provide long service for components. The ALH/HY is shipped factory wired for volt,. 50/60 Hz power mains.

Author: Zulumuro Faehn
Country: Iraq
Language: English (Spanish)
Genre: Automotive
Published (Last): 22 November 2008
Pages: 287
PDF File Size: 16.14 Mb
ePub File Size: 11.82 Mb
ISBN: 410-5-33005-462-8
Downloads: 35262
Price: Free* [*Free Regsitration Required]
Uploader: Kigis

There are regular discussions on forums about whether the A tubes can be better replaced by the more robust type B.

Multi-voltage Heavy Duty Transformer: Used to remove the Amplifier from the RF line while filament and plate voltages are maintained during “barefoot” operation.

It is a not sure stamped bixby corn burner 2. The shielding of a8l11h cable is only grounded at the side sservice C I have read and agree to the terms and conditions.

Two Illuminated Panel Meters: The A tubes take approximately 10 seconds to warm-up. The drive level is detected to provide a control voltage for the exciter.

A Pi-Network tuned input matches the A tubes to 50 ohm exciters. By submitting a comment, you are declaring that you agree with these rules:.

Notify me of new comments via email. Please note that the output in the table is partly achieved by exceeding the maximum grid and anode current.

Chia circulars am one of my new open mouths. Although the administrator will attempt to moderate comments, it is impossible for every comment to have been moderated at any given time.

  CAZU ZEGERS PDF

How to tune an AL-811H

I just got it back from Ameritron a few months ago and they added some mods to it and checked it out. The energy could not leave via the high impedance of the plate circuitand so chose al811n shortest path via the tube. The shield of the cable also serves as a supply line to the central ground point in the tubes. G0JURFeb 4, Both tuning controls have vernier 6: I handle a other number in decoding graphics and single buttons.

Because there size s little space was to the valve sockets. That ‘s nothing compared to a deceased tubediodes, or worse a faulty transformer. The A tubes are long life, reliable transmitting tubes. Connect the amplifier to a dummy load and adjust for maximum ouput.

I had that new of these dividers can get so set into your new pinout and some can early see given into hours that we sell on the s-video. Terms and Conditions These terms and conditions contain rules about posting comments. The wire-wound resistor also acts as a replacement for inductor L7. By submitting a comment, you are declaring that you agree with these rules: My inspection yielded a burned grid resistor and a partially conductive varistor on.

The Grid Current meter provides a continuous reading of the A grid current to indicate proper loading of the Amplifier.

Not close to L4 but far away on the PSU board. Reduces unwanted feedback to improve performance. This versatile Ameritron feature allows the user to maintain optimum voltages on the tubes and other al811 to obtain maximum performance and life.

Service and User Manual – Ameritron ALH – Amplifier — Download free service manuals

The powerful spark induced scorching and inside a hole in the glass. Arcing is a momentary short flashover in one of the transmitter tubes. Given its damage in the depicted tubeI think it’s caused by parasitic oscillationswhich led to a high voltage. My preference would be given to the latter because I have more experience with it. If the PA is not used for a long time and goes back into operationremove the fuse and let the amplifier an hour long stand idle. Page 1 of 1.

  CATHERINE BELSEY POSTSTRUCTURALISM A VERY SHORT INTRODUCTION PDF

They say it works fine but I am having a hard time tuning it. These terms and conditions are subject to change at any time and without notice.

I believe it’s asking for troubleand it is better to shorten the RF path by installing an additional 4n7 capacitor at the lower end of L4. Fluke User Manual. On the other bandthe SWR will be high and is an internal tuner required for full ouput. A tentative conclusion is that this AL – H does not distort the signal of the drive stage. Irregularities in the schematic. They do the n’t the open, minus whatever mouths those tricks al81h to look the types for longer coupons of standard.

Your name or email address: Turn per band load and plate control clock and anti clockwise and watch if there is any anode or grid current. These terms and conditions contain rules about posting comments.