Retire el ATV del embalaje y compruebe que no presenta daños. .. Consulte el manual del programación (BBV) para una descripción completa del. Manual de programación Altivar® 06/ Contenido .. Altivar 31 (ATV31) es una familia de variadores de velocidad de ~ (c.a.) de frecuencia ajustable. Manual de programación. ATV Manual de programación Manual de programación · altivar-machine-atv ATV Manual de programación.

Author: Nirisar Dagrel
Country: Anguilla
Language: English (Spanish)
Genre: Art
Published (Last): 10 February 2010
Pages: 254
PDF File Size: 16.17 Mb
ePub File Size: 12.41 Mb
ISBN: 832-8-99682-223-8
Downloads: 80519
Price: Free* [*Free Regsitration Required]
Uploader: Taujinn

Variateurs de vitesse progrramacion moteurs asynchrones. The high frequency equipotential ground connection between the drive, motor, and cable shielding does not eliminate the need to connect the ground PE conductors green-yellow to the appropriate terminals on each unit. Altivar 61 C1 EMC.

Variadores Schneider

The shielding must be clamped tightly to the metal plate to improve electrical contact. Leave sufficient free space so that altivra air required for cooling purposes can circulate from the bottom to the top of the unit. Altivar – Botek Otomasyon. These manual describes the assembly, connection to the bus or network, signaling, diagnostics, and configuration of the communicationspecific parameters.

Solve Telemecanique ATV31 problem

Installation, adjustment, repair, and maintenance must be performed by qualified personnel. Shielded cable for motor connection with shielding connected to ground at both ends.

COM To ensure the functioning of the site, altlvar use cookies. Wait for the display to go off completely. Nonetheless, the nominal drive current should be derated if operation above 4 kHz needs to be continuous. Before starting up the drive, please check the following points regarding mechanical and manuql installations, then use and run the drive.


The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. Read and understand this manual before installing or operating the Altivar drive. Altivar – Schneider Electric Altivar alhivar Installation manual This manual describes how to install and wire the drive.

Failure to follow these instructions can result in injury or equipment damage.

Altivar – Variateur de vitesse BBV If the installation includes several drives, provide one “residual current device” per drive. For control and speed reference circuits, we recommend using shielded twisted cables with a pitch of between 25 and 50 mm 1 and 2 in. We share information about your activities on the site with our partners and Google partners: These detected faults can also be reset by cycling power to the drive or by means of a manuao input or control bit.

Free space u 50 mm 2 in. Choice of associated components: Supplied with the aktivar Fix the EMC equipotentiality mounting plate to the holes in the ATV heatsink using the 2 screws supplied, as shown in the drawings below.

Communication variables guide The Communication variables manual defines the drive control processes and the drive variables which can be accessed by the communication buses: Where local and national codes require upstream protection by means of a residual current device, use a type A device for single-phase drives and a type B device for three-phase drives as defined in the IEC Standard Altivar – ENEL.


Control Keep the control circuits away from the power cables. Accidental grounding can result in unintended activation of drive functions. If the DC bus capacitors do not discharge completely, contact your local Schneider Electric representative.

Wire the drive see page 17 v Connect the motor, ensuring that its connections correspond to the voltage. Keep the power cables separate from circuits in the installation with low-level signals detectors, PLCs, measuring apparatus, video, telephone. Receive and inspect the drive v Check that the catalog number printed on the label is the same as that on the purchase order.

The switching frequency is adjustable from 2 to 16 kHz. Certain detected faults can be programmed for automatic restart after the cause has disappeared. EMC plate supplied with the drive, to be installed as indicated on the diagram. Please refer to the programming manual.