ASTM A313 PDF

ASTM A/AM: Standard Specification for Stainless Steel Spring Wire. Copper. % max. Phosphorus% max Nickel. – %. Silicon. % max Nitrogen% max. Tensile Strength Table (ASTM-A) *KSI. Over. Stainless Steel Wire, AISI / ASTM A , Cr % Ni %, 28 () , 10 (), , C, Request a Quote. AISI ASTM A , Cr

Author: Dogore Tygogal
Country: Brunei Darussalam
Language: English (Spanish)
Genre: Science
Published (Last): 19 October 2015
Pages: 352
PDF File Size: 17.24 Mb
ePub File Size: 3.96 Mb
ISBN: 808-7-38565-511-9
Downloads: 51911
Price: Free* [*Free Regsitration Required]
Uploader: Toshakar

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. After etching the surface of the wire specimen it shall be examined under a 10 power microscope for aastm, seams, pits, die marks, scratches, or other imperfections tending to impair the fatigue resistance of springs.

The wire shall withstand the minimum number of bends speci? Originally approved in Within the text and tables, the SI units are shown in brackets. A superscript epsilon e indicates an editorial change since the last revision or reapproval. A piece not more than 10 in. Users of this standard are expressly advised that determination qstm the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

A number in parentheses indicates the year of last reapproval. Combining values from the two systems may result in nonconformance with the speci?

Failure to comply with the general requirements of Speci? This standard has been approved for use by agencies of the Department of Defense.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. After this treatment, the specimen coil shall show uniform pitch with no splits or fractures.

  KANTECH KT 400 PDF

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? One specimen shall be taken from every ten coils in the lot. Link to Active This link will always route to the current Active version of the standard. This guide covers standard specification for austenitic and age-hardenable stainless steel round spring wire intended especially for the manufacture of springs.

Our staff has the experience to assist you in selecting the best stainless steel alloy for your application and to manufacture a custom spring steel wire that meets or exceeds your expectations. Such requirements may include, aetm are not limited to the following: Lubricating coatings, which are insoluble in acid etch solution, shall be removed before etching.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. It has superior cold forming properties and exhibits short term tensile and creep strength at temperatures up to degrees F.

J Numbering Metals and Alloys4 3. Type Class ast shall be stress relieved following fabrication and meet the requirements shown in Table 4. Current edition approved Sept. NOTE 1—A typical ordering description is as follows: A — 96 Steel Spri Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

Stainless Steel Wire Springs – Stainless Steel Alloy Springs | General Wire Spring Company

You can be assured that your springs will be delivered to you fast and ready for your production line. It exhibits superior fatigue properties, elasticity, strength-to-weight ration, high yield strength, ductility, and good corrosion resistance, at temperatures up to degrees F. This standard has been approved for s313 by agencies of the Department of Defense. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  LIBRO ENUMA ELISH PDF

Type Class 2 shall be stress relieved following fabrication and meet the requirements shown in Table 4. Go to Navigation Go to Aetm.

Stainless Steel Wire Springs

a133 The tensile strengths to be obtained following the prescribed heat treatment are shown in Table 2 and Table 3 for hardened wire. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The nominal as-drawn tensile strengths are provided as a guide for the spring manufacturer.

Click here to contact us today or call us at Call today to see how we can solve your stainless steel spring manufacturing challenge. After etching the surface of the wire specimen it shall be examined under a 10 power microscope for q313, seams, pits, die marks, scratches, or other imperfections tending to impair the sstm resistance of springs. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

Stainless Steel 302

The wire shall lie? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Following fabrication Type and Grade XM shall be age or precipitation hardened to produce their maximum strength properties.