ASTM B、ASTM BM铜镍锌合金(镍银)及铜镍条和棒材_信息与通信_工程 科技_专业资料。Designation: B /B M – 00 Standard. ASTM B/BM Standard Specification for Copper-Nickel-Zinc Alloy ( Nickel Silver) and Copper-Nickel Rod and Bar. standard by ASTM. SAE J, J, Cu( min) Pb max* Fe Zn 1 max* Ni Mn 1 max, 52, 18, CuNi 70/30, UNS C, ASTM B, B, B, Cu rem.
|Published (Last):||19 August 2006|
|PDF File Size:||9.97 Mb|
|ePub File Size:||19.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
This standard is n151 to revision at any time by the responsible technical committee and must be reviewed every? This standard has been approved for use by agencies of the Department of Defense.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Wstm abstract is a brief summary of the referenced standard. Limits may be established and analysis required for unnamed elements by agreement between the manufacturer and the purchaser. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
ASTM International – Standard References for ASTM B / BM – 13
This specification establishes the requirements for copper-nickel-zinc and copper-nickel rod and bar for general application produced from Copper Alloy UNS Nos. Rejection and Rehearing C and C are for product intended for welding applications. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.
Current edition asgm Oct.
ASTM B151 Round Bar Suppliers Manufacturer Stockist
C and C Min Rod: The values stated in each astn may not be exact equivalents; therefore, each system shall be used independently of the other. ASTM does not give any warranty express or implied b115 make any representation that the contents of this abstract are accurate, complete or up to date. C and C O60 H04 round, hexagonal, and octagonal rods and square bars round, hexagonal, and octagonal rods and square bars all sizes up to 3?
C, C, C, and C Min Max H01 60  80  75  95  H04 80   90   70  65  60  90  80   85  75  80  70  95  90  H04 68  88  75  95  A number in parentheses indicates the year of last reapproval. Combining values from the two systems may result in nonconformance with the standard. C and C O60 round, hexagonal, and octagonal rods and square bars up to 1?
Government shall conform to the special government regulations speci? Link to Active This link will always route to the current Active version of the standard. The chemical composition, temper, annealed temper grain size, and tensile astj requirements are detailed.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Within the text, SI units are shown in g151. Number of Tests and Retests NOTE 2—The purchaser should confer with the manufacturer or supplier concerning the availability of a speci? Test results asm all specimens shall conform to the product speci? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
C and C were added. Historical Version s – view previous versions of standard.
A superscript epsilon e indicates an editorial change since the last revision asgm reapproval. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
ASTM B Copper Nickel Round Bar · B C/C Bar
Last previous edition B — The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Mechanical Property Requirements Samples of the rejected product shall be taken in accordance with the product speci? Combining values astmm the two systems may result in nonconformance with the standard.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. C and C are for product intended for welding applications. Materials and Manufacture 6. Grain Size of Annealed Tempers 9. Dimensions, Mass, and Permissible Variations Originally published as B — v151 T.