B 65162E PDF

D External dimensions. D Connections. D Connection of motor. FANUC CONTROL MOTOR AMPLIFIER α series DESCRIPTIONS. B–E. B–E. FANUC AC SPINDLE MOTOR α series PARAMETER MANUAL B– E. FANUC SERVO AMPLIFIER α series DESCRIPTIONS. B–E. FANUC SERVO AMPLIF IER @ series DESCRIPTIONS BE/03 The export of this product is subject to the authorization of the.

Author: Malagal Zolok
Country: Cyprus
Language: English (Spanish)
Genre: Video
Published (Last): 8 September 2012
Pages: 443
PDF File Size: 13.25 Mb
ePub File Size: 18.91 Mb
ISBN: 947-4-99367-296-9
Downloads: 14327
Price: Free* [*Free Regsitration Required]
Uploader: Kagajinn

F Connect the power supply lines and power lines to the appropriate terminals. This may also shorten the life of the semiconductors. Spindle Amplifier Module Connection Diagram. F If the motor makes any abnormal noise or vibration while operating, stop it immediately.

If the detectors are not properly adjusted, the motor may not rotate normally or the spindle may fail to stop as desired. When other than a FANUC power transformers is to be prepared by the user, it must satisfy the transformer specifications indicated in 1 of Section 5.

Therefore, note the following when installing the 651662e.

Fanuc B-65162 Manuals

If the motor operates abnormally, perform an emergency stop immediately. If the amplifier is used continuously with an excessive load applied, the amplifier may be damaged. When removing the case or PC board, take care not to lose any screws. If any clearance is left between the power magnetics cabinet and the surface on which the amplifier is mounted, dust entering the gap may build up and prevent the normal operation of the amplifier.


Connect the other ground terminal of the terminal block v the frame ground.

High—resolution magnetic pulse coder for motors and spindles 4. See the section 5. The flow of cooling air must not be obstructed. Load Meter Voltage LM. Servo Amplifier Module Connection Diagram. F Check that the amplifier is securely mounted in the power magnetics cabinet.

The table below lists the maximum number of modules which can be connected. See the allowable ambient temperatures and other requirements, given in the corresponding descriptions. Selecting a Regenerative Discharge Unit.

From motor power cable M5 screw??? This causes a high—frequency leakage current to flow via the ground drift capacitance in the motor winding, power cable, and amplifier.


Adequate countermeasures against noise are required to maintain normal operation of the amplifier. Notes on the Emergency Stop Circuit Configuration. Open the door of the power magnetics cabinet; Leave the control power of 651662e power supply module on; Place the machine in the emergency stop state so that the power being input to the g is shut off; Then, replace the battery.

The surface of the radiator and regenerative discharge unit become extremely hot. F Notes on contacting FANUC Inform FANUC of the details of an alarm and the specification code of 651622e amplifier so that any components required for maintenance can be quickly secured, and any other necessary action can be taken without delay. Do 651162e install the modules far apart from each other; install them in series.

  ETON PA 2802 PDF

Also, keep the specifications at hand. The operator must be familiar with these descriptions. It contains a fuse. When installing the amplifier in a power magnetics cabinet which is designed to draw in air, fit an air filter to the air inlet. A cable to be shielded must be securely connected to the ground plate, using a cable clamp or the like.

F Store the manuals in a safe place. Explanation of Spindle Synchronization Control. If a screw is lost inside the nit and the power is turned on, the machine may be damaged. The ordering drawing numbers and specifications of power transformers manufactured by FANUC are listed below. The cover on the front of the amplifier carries a label 65612e a specification code.

Fanuc Servo Amplifier Alpha Series Descriptions E pdf – CNC Manual

Connect the ground terminal of the metal frame to the frame ground. Otherwise, the cooling efficiency will be reduced so that the characteristics of the amplifier cannot be guaranteed. Note that the specification of the coil voltage of a magnetic contactor may differ depending on the supply voltage and frequency used.

Users should also read the relevant description in this manual to become fully familiar with the functions of the servo amplifier.