A M E R I C A N A R C H I T E C T U R A L AAMA (Formerly CAWM) Standard ( Formerly CAWM ) Standard Practice for Installation of Windows with a. AAMA (Formerly CAWM ). Standard Practice for. Installation of Windows with a Mounting Flange in. Stud Frame Construction. document was CAWM , Standard Practice for the Installation of Windows In , and using the CAWM as a template, ASTM started work on a.
|Published (Last):||17 November 2008|
|PDF File Size:||17.2 Mb|
|ePub File Size:||3.84 Mb|
|Price:||Free* [*Free Regsitration Required]|
See Figure 5 Method B A strip of approved flashing material shall be at least mm 9 in wide.
While the use of these installation instructions More information. Amazon Inspire Digital Educational Resources.
The sealant applied horizontally across the cawk should not extend beyond the jamb sealant. 4000 the first strip horizontally immediately below the sill, cut it sufficiently long to extend past each side of the window, so that it projects even with the vertical jamb flashing to be applied later.
Flashing material shall carry continuous identification. AmazonGlobal Ship Orders Internationally. Jamb Flashing Method A See Figure 2 Next, fasten strips of flashing along each vertical edge jamb of the opening. Any local building code requirements More information.
American Architectural Manufacturers Association. Once a method is selected, all procedures of that method shall be performed in the described sequence.
Architectural Testing 4 Rancho. Shim and adjust the window as necessary to achieve a plumb, square and level condition, as well as centering the window in the frame opening.
On newer versions of Microsoft Word.
Place Waterproof Sill Shims D. See and discover other items: The application of sealant to the exterior surface of the mounting flange may not be necessary if using a selfadhesive type flashing over the mounting flange. A fin projecting from the window frame parallel to the plane of the wall, also known as a nailing fin, for the purpose of securing the frame to the 955. This voluntary specification was developed by representative members of AAMA as advisory information and published as a public service.
Shopbop Designer 4400 Brands. The responsibility for protecting any flashing material from damage caused by weather, other trades, or vandalism, and properly integrating the flashing system into the weather resistant barrier for the entire building, is the responsibility of the general contractor or his designated agent Penetration Flashing Material Flashing material shall be barrier coated reinforced and shall provide twentyfour 24 hour minimum protection from water penetration when tested in accordance with ASTM D We urge you to read and follow the attached installation instructions.
AAMA Pubstore Product Listings –
See Figure 4B In each direction from all corners there shall be a fastener within mm 10 inbut no closer than 75 mm 3 in to prevent frame distortion or fracture of joint seals. Search by product code or category or leave the product code field blank to see a list of all AAMA publications. Window Installation Guide This guide provides basic information.
Remove debris that will. Installation may require two people. Window Installation Method A Pactiv Building Products believes the information and recommendations herein to be More information.
This raises two questions. Failure to follow these guidelines will forfeit all warranties More information. Available in White and Tan homogenous window frames, More information. Instructions for Wall Installations: Any building used or intended primarily for a single or multiple family dwelling.
This practice covers the installation of windows in residential buildings of no more than four 4 stories in height. Chevrolet Sensor Crankshaft Position. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens, More information. Prior to installation, store windows in a near vertical position in a clean area, free of circulating dirt or debris and protected from exposure to weather elements Field-applied protective coatings may damage window sealants and gaskets and may not be recommended.
A copy of this letter will be provided to that task group for consideration and may result in this apparent inconsistency being clarified in a future edition of the document. Any local building code requirements. Hinged and pivoted windows may require additional fasteners located near the hinge or pivot point. Withoutabox Submit to Film Festivals. Storage Store the siding in a dry and ventilated area. An overview of the proper flashing. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification More information.
If you have not installed a door previously, we recommend you use a professional installer. The surface or surfaces of a wall responsible for preventing water infiltration into the building interior.
All AAMA documents are periodically reviewed and cawk. Customers also shopped for. The AAMA Western Caw currently has a task group looking at developing guidelines for forensic investigations of window installations. Provide a minimum of one-quarter inch More information. Actual conditions in buildings vary greatly, and in some cases substantial additional care and precaution will have to be taken. Section Architectural Metal Panels.
However, the two statements are not really in conflict with each other.