Manuals and User Guides for Panasonic CS-S10PKH. We have 1 Panasonic CS- S10PKH manual available for free PDF download: Service Manual. View and Download Panasonic CS-S10PKH service manual online. CS-S10PKH Air Conditioner pdf manual download. Also for: Cs-s13pkh, Cs-s15pkh. Panasonic CS-S10PKH Manual Online: Cs-s18pk Cs-s24pk. Indoor Electronic Controllers, Cross Flow Fan and Indoor Fan Motor Removal Procedures.

Author: Zulkis Fautaxe
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Automotive
Published (Last): 16 February 2012
Pages: 305
PDF File Size: 1.11 Mb
ePub File Size: 9.97 Mb
ISBN: 673-7-22879-755-8
Downloads: 80853
Price: Free* [*Free Regsitration Required]
Uploader: Bazahn

Cable connection to the power supply through Isolating Devices Disconnecting means. Electronic Circuit Diagram Page 70 10 Remove the tapes and connect the power supply cord and connection cable between indoor unit and outdoor unit according to the diagram below.

Make sure that the needle in the gauge does not move after approximately five minutes. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.

Remote control is enable again. Installation Instruction Except Myanmar Press the CHECK button on the remote control for about 1 second with a pointed object to transmit signal to main unit.

Panasonic CS-S10PKH Service Manual: Cs-s18pk Cs-s24pk

To change remote control transmission code, short or open jumpers at the remote control printed circuit board. Remove burrs from cut edge. Ensure that the capacitor has discharged sufficiently before proceeding with repair work.

Otherwise, it will cause the set to fall, water leakage, fire or electrical shock. Remove 4 screws holding the control board then pull out the control board. This control will begin 1 minute after the compressor starts. The changes of frequency are as below. Remove the valve caps of both of the 2-way valve and 3-way valve.


This control stopped if s1pkh Compressor stopped.

Panasonic CS-S10PKH Manuals

High fan speed Piping length: Power supply point should be in easily accessible place for power disconnection in case of emergency. Disassembly and Assembly Instructions Mild Dry Cooling Operation Fan motor can be removed after the removal of cross flow fan. Open the front panel and ca door by loosening the screw.

Battery insert Sensitivity Level 3: The sunlight sensor sensitivity could be adjusted: The indoor fan will operate according to pattern below. Wiring Connection Diagram Indoor Unit 7. Remove screw to remove terminal board complete. Do not wrench the fasten terminal. When error code happened, the unit is able to operate without sunlight sensor. Using of existing R22 piping, fl are nut and tools may cause abnormally high pressure in the refrigerant cycle pipingand possibly result in explosion and injury.

It does not contain warnings or cautions to advise non-technical cw of potential dangers in attempting to service a product. Powerful Mode Operation Printed in Malaysia SB High fan speed o Piping length: Sensor Thermistor Characteristics 40 30 20 10 0 10 20 30 40 0 50 o 20 40 60 cz Temperature oC Temperature C 45 8. Putty or caulking compound 58 Do not place any obstacles which may cause a short circuit of the discharged air.


Cs-s10pkh Cu-s10pkh malaysia Only. Cross flow fan Reminder: Ccs supply connection to a circuit breaker for the permanent connection. Remove the screw that holding the cross flow fan and fan motor axis. It may need two people to carry out the installation or servicing work. Electronic Circuit Diagram 8. Installation Instruction Diagram Except Myanmar Otherwise, it may cause electrical shock and fire in case equipment breakdown or insulation breakdown.

There should not be any heat source or steam near the unit. After completion of installation or service, confirm there is no leakage of refrigerant gas.


Fan speed will be adjusted accordingly in this control. Figure 8 Failure to heed this caution may result in electric shocks. Otherwise, it may cause electrical shock in case equipment breakdown or insulation breakdown. In operation after breakdown repair, the Timer LED will not blink.

Enter text from picture: Align center of piping to valve and then tighten with torque wrench to the specified torque as stated in the table. Figure 9 Cross Flow Xs Reminder: Location Of Controls And Components 3.