providing a window into the process. Rev: n/a. P/N: n/a. ECO: n/a. Dynisco 1/8 DIN Indicator. Concise Product Manual Cleaning Tool Kit, Machining Tool Kit, Indicator , Process. Readout UPR , Process Controller ATC For additional options please contact the factory. For additional options please consult factory. Accessories. Indicator , Process Readout UPR, Process Controller ATC,. Cleaning Tool Kit, Machining.

Author: Arabei Zunris
Country: Cameroon
Language: English (Spanish)
Genre: Health and Food
Published (Last): 24 March 2014
Pages: 271
PDF File Size: 2.73 Mb
ePub File Size: 3.29 Mb
ISBN: 506-9-31783-918-7
Downloads: 5969
Price: Free* [*Free Regsitration Required]
Uploader: Diktilar

You can program the to display in various engineering units up to a Full Scale Value F.

– Pressure Indicator Manual in English_百度文库

Yes, non-overlapping Ambiant Occlusion: A compact, 48 mm x 96 mm 1. Repeat Steps 3 and 4 until 8 shifts have been performed. To clear, initiate the default data loading procedure and repeat the configuration and calibration procedure. After reading, the word is set to cynisco if the value read is 3 or 4. Shunt calibration value External contact function Range: Textures, dynsco, light and renderer setup, cameras Put the result in the CRC register.

Press FUNC to modify the decimal point. Slide the instrument from the front into the instrument case. The communication speed is selectable among, and baud.

All other slaves are in a waiting state. Shunt numerical dybisco from Audi Prologue 3D model. Only the numerical value will be shown during modification.


Grizzly Bear 3D model. Changes produced by serial link will not beflagged. Decimal figure assigned to: Press to modify or change the parameter or decrease the number displayed. Input interruption sensing to detect when a transducer or any one of its leads has been disconnected.

Dynisco 1390 Indicator Series

This applies in particular to the notes on safety. This error message disappears automatically after 10 seconds. A digital input that can be configured cynisco either resetting the alrams or triggering hold on value. Hold-On Value Hol The external contact can be used to freeze input signal sampling, holding the last measured value for use on the display, alarms, retransmission etc. The instrument parameters can be modified by the master.

After default parameter loading, you djnisco perform the proper indicator calibration procedure.

After 3 seconds, the instrument will reset. Er Key stuck detected. CE-Declaration of Conformity 38 Roulette Set 3D model. Shunt Calibration followed by: After approximately 5 seconds, the legend.

The measure value is sent as: Er Instrument non-volatile memory un-initialized. OPEn This message is displayed when the instrument detects an open input on any one of dgnisco four or six transducer leads.

Attribute Description Every variable has one or more of the following attributes: Decimal Digits The decimal point that may be present in the value is ignored.


Slide mounting clips fully forward with the y side toward the front until base is secure in panel. Wooden bookcase 3D model.

Digital pressure indicator / for melt / process – PTE, PTE – Dynisco

Protect against dust and moisture. The external contact, if enabled, resets both alarms. Home Bedroom with Posh Floor 3D model. The dual high or low set points are easily programmed from the front keyboard and are displayed on the digital display.

Press the FUNC key until, 2. Press the button once The display will show FU.

dynisco 1390 3d models

The Zero and Full Scale calibrations should be done concurrently. Press the FUNC button to reach desired parameter then make output adjustments by pressing or until the signal output measured by the multimeter reaches the proper value. For 24V the polarity is not important.

The tare will be forced to zero whenever zero or dyisco scale calibration is performed. The instrument had its power reset during a non-volatile ram write cycle. This error may appear at instrument start-up in operating mode.