INTERSEAL 670HS MSDS PDF

INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Bralkree Meztill
Country: Iraq
Language: English (Spanish)
Genre: Sex
Published (Last): 28 October 2009
Pages: 135
PDF File Size: 13.8 Mb
ePub File Size: 5.35 Mb
ISBN: 151-7-14220-237-5
Downloads: 88635
Price: Free* [*Free Regsitration Required]
Uploader: Nezshura

Mouse over image to zoom. Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates.

INTERSEAL HS PLATINUM GREY MSDS Download

Certification is for tanks greater than gallons For application to a wide variety of substrates including hand prepared rusty steel, mzds blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. Low or high temperatures may require specific application techniques to achieve maximum film build.

Premature exposure to ponding water will cause a color change, especially in dark colors. Be the first to write a review for this product! In common with all epoxies Interseal HS will chalk and discolor on exterior exposure. Prior to paint application all surfaces should be assessed and treated in accordance with ISO Typical thicknesses will be between milsmicrons. Trowel or roller can be used for small areas. However, msdd phenomena are not detrimental to anti-corrosive inteerseal.

  DIN 41773 PDF

Interseal HS can be used as a non-skid deck system by modification with addition of GMA crushed flint aggregate. Dry bristle brushing will normally be adequate for accumulated dirt. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat intersesl brush to ensure thorough wetting out of the substrate by Interseal HS.

INTERSEAL HS – PART B (REGULAR) – L ( :1)

Do not thin more than allowed by local environmental legislation. Aged Coatings Interseal HS is suitable for overcoating a limited range of intact, tightly adherent aged coatings.

A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. Preferred application is by a suitable large tip hopper gun e. Consult International Protective Coatings for further details.

With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Avoid using a mixture of application methods whenever possible.

Press and move to zoom. Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems. Surface preparation The performance of this product will depend upon the degree of surface preparation. Please consult International Protective Coatings for alternative recommendations.

Accumulated dirt and soluble salts must be removed. If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS.

When applying by methods other than airless spray, the required film build is unlikely to be achieved. NSF Certification is for tanks greater than gallons Soluble salts should be removed by fresh water washing. Always mix a complete unit in the proportions supplied. A surface profile of mils microns is recommended.

  LC2412 BEHRINGER PDF

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in 670sh appropriate manner.

Varnish Hybrid Water base. However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used. However, it can be used over suitably primed surfaces. Level of sheen and surface finish is dependent on application method.

Brush Typically mils microns can be achieved Roller Typically mils microns can be achieved How to use Mixing Material is supplied in two containers as a unit. It is also possible to apply to damp surfaces in some circumstances. Further information is available from International Protective Coatings.

Application should then be to a suitably primed surface.

Sagola or Air texture gun fitted with smds mm nozzle. Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both atmospheric exposure and immersion service.

Once the unit has been mixed it must be used within the working pot life specified.

Alternatively, a broadcast method of application can be used. Typically this would apply to C or D grade rusting in this standard.