These are all list of error code in Canon iR/iR more to come, i hope your machines works fine and never get error. E Main cause. fixing oil, the error code is indicated. E The rated voltage of the power supply and that of the fixing unit do not match. E Clock pulses fail to be generated. canon ir is showing an error codes E How it will solve? Your error code is for the fixing unit solve by checking the follwoing: 1. Fixing lamp.

Author: Malazahn Jujind
Country: Puerto Rico
Language: English (Spanish)
Genre: Sex
Published (Last): 24 July 2017
Pages: 135
PDF File Size: 19.28 Mb
ePub File Size: 12.93 Mb
ISBN: 677-1-85653-852-1
Downloads: 86312
Price: Free* [*Free Regsitration Required]
Uploader: Zulkigul

The copy data controller orthe remote diagnostic device is faulty. Mode ofDetection The puncher does not leave home position when the horizontal registrationmotor has been driven for 4 secs. The thermal switch TP1 has an open circuit. The waste toner feedscrew is faulty. The communication line has an opencircuit.

After replacing the fixing web, be sure to reset the two web counters in service mode: Mode ofDetection The alignment plate home position sensor does not turn on whenthe alignment motor has been driven for 0. Main Cause The hard disk fan FM7 is faulty.

The main controller PCB. Main Cause The cooling fan Cod is faulty. The inverter PCB is faulty.


About me indra Indonesia Just want to share View my complete profile. The SSR has a short circuit.

Subscribe To Posts Atom. The sub thermistor TH2 has detected overheating. The reader controller PCB isfaulty. The folding motor M2S is faulty.

Canon iR5000 Service Manual: Error Codes; List Of Error Codes

Mode ofDetection The number of detection pulses of the folding motor clock sensordrops below a specific value. The alignmentmotor M3 is faulty. The paperpositioning plate motor M4S is faulty. Main Cause The shutter open sensor Or6000 is faulty. The saddle stitcher controller PCB is faulty. The stitch motor front, M7S is faulty.

Error Code Canon IR error E

The wiring is faulty short circuit, opencircuit. The main thermistor TH1 has poor contact or an open circuit. Mode ofDetection The guide home position sensor does not turn on when the guidemotor has been driven for about 0.

The safety area switch MS3 is faulty. The paper push-on plate leadingedge position sensor PI15S is faulty. Newer Post Older Post Home.

The potential measurement PCB is faulty. The alignment motor M5S is faulty. The fixing web has been taken up. The paperpush-on plate leading edge position errkr PI15S is faulty.

The hard disk drive isfaulty.

The stitch motor rear, M6S is faulty. The paper push-onplate motor M8S is faulty.


Mode ofDetection An error has occurred in the communication between the various. The drum motor M1 is faulty. Main cause The connector has poor contact.

The finisher controller PCB is faulty. The delivery door switch MS3S is faulty. The primary charging assemblycooling fan FM2 is faulty. The main thermistor TH1 has a short circuit. The waste toner clock sensor MSW2 is faulty. The punch motor M1P is faulty. The stapler shift motor M4 is faulty. The stapler cod M6 is faulty. Mode ofDetection Communication between the height sensor and the finisher controllerPCB is not possible, or communication data has an error.

Crazy It6000 Copiers Loading Mode ofDetection The stapler does not leave eror position when the stapler motorhas been driven for 0. Main cause The LAN card is faulty.

The swing guide open sensor PI18 is faulty. The feed fan FM1 isfaulty. Mode of Detection The stitcher home position sensor rear does not turn off when thestitch motor rear has been rotated CW for 0. The finisher controller PCB isfaulty.